You can also set the device up directly from the Total Connect 2.0 app. Then follow the instructions on the screen to integrate your SkyBell device with your smartphone. Download the app for free from the App Store or the Play Store, and create a SkyBell account. Now that the SkyBell has been installed, you can set it up with the SkyBell app. The device should power on once power has been restored.ĥ. Once the SkyBell has been added, you can return power to the doorbell. Tighten the set screw at the bottom to ensure that the SkyBell remains nice and secure. The device should easily slide in and snap into place. Then, take the SkyBell, line it up at the top, then swing the bottom into place. Start by loosening the set screw at the bottom of the mounting plate. You can then apply the SkyBell itself over the mounting plate. For this device, whether using AC or DC power, polarity is not important.Ĥ. Make sure that the wires are not touching. Finally, wrap the copper portion of one of the wires around one of the terminals and screw it into place. Then, loosen the wire terminals on the mounting plate. Strip your existing doorbell wires so that they can be installed. This is where you will wire power to the device. On the left side of the mounting plate, you will see two adjacent terminals where wires can be screwed in. Make sure that the mounting plate is nice and secure before continuing.ģ. You will then screw in the mounting plate using the included screws. If you are installing the mounting plate into wood, then you will want to make pilot holes that are slightly smaller than the included screws. The mounting plate can then be tightly screwed in using the included screws. You will use this drill bit to create the holes and then insert the yellow wall anchors into the holes. You may need a drill bit for drilling into brick, masonry or stone. Slide the wires through the SkyBell mounting plate and use the included screws to install the mounting plate into the wall. Make sure that you can still access the wires, as you will need them for the SkyBell installation.Ģ. Unscrew the old doorbell from the wall and detach its two wires to remove it. Please note, before installing the SkyBell Doorbell, you will want to shut off the power to your doorbell to prevent any electrical problems or injuries.Ĭomplete the following steps to install a SkyBell DBCAM HD Video Doorbell:ġ. Once you have made sure that your setup is compatible, you will be ready to install the SkyBell Doorbell Camera. Failure to include this resistor will cause damage to the SkyBell. The power terminals for the SkyBell are not marked for polarity. When AC or DC power is used for the SkyBell, polarity is not important. The other end of the resistor will connect to the opposite side of the power supply. One end of the 10 ohm/10 watt resistor should connect to the other screw terminal on the SkyBell's mounting plate. This means that one wire will go straight from the AC or DC power supply to one of the screw terminals on the SkyBell mounting plate. If the SkyBell will be installed in a location with no pre-existing doorbell, and no mechanical chime will be used, then a 10 ohm/10 watt resistor (not included) must be installed in series between the SkyBell and the power supply. You will need a wire to complete the installation. Please note that this transformer does not come with a wire for connecting it with the SkyBell. An example of a compatible transformer is the MG Electronics ST-12500. The Skybell will connect with one transformer wire and one doorbell chime wire. The power supply for the doorbell will need to be 10 to 36 VAC, 10VA or 12 VDC. The SkyBell connects with a wired, mechanical doorbell chime and a low-voltage transformer. It can then be set up with the SkyBell app.īefore installing the SkyBell, you will want to make sure that the chime and the power supply in your house is compatible. The SkyBell can then be snapped into place on the plate to power it on. You will then install the SkyBell mounting plate and screw in the existing wires. You can install a SkyBell Doorbell Security Camera by first removing your existing doorbell.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |